How To Change The License Plate Light Bulb On A 2006 Acura Rl

Acura MDX License Plate Light Bulbs Replacement Guide
How to change a burnt out license plate calorie-free bulb in the tailgate of a 1st generation 2001-2006 Acura MDX.

2006 MDX License Plate
Left License Plate Light
Loosen Counterclockwise This automotive maintenance tutorial was specifically created to assist owners of the first generation (2001, 2002, 2003, 2004, 2005 & 2006) Acura MDX in irresolute a burnt out license plate low-cal bulb located in the two housings fastened to the tailgate door for the cargo surface area.

Owners of other Acura or Honda vehicles such as the RDX, ILX, TLX, RLX, TL, CL, RSX, RL, TSX, ZDX, NSX, Integra, Pilot, Accord, Civic, Fit, Clarity, CR-Five, CR-Z, HR-V, Odyssey, Element and Ridgeline may also discover these DIY instructions to exist helpful.

The compatible replacement miniature wedge base light bulb part number is 168 (also known every bit W5W).

You could also install some brighter 168 LED bulbs.

The only tool needed to admission and replace the bulbs is a standard Phillips head screwdriver.

Longer Left Side Screw
Remove Right Side Screw
Shorter Right Side Screw Each of the 2 license plate light housings are held in place to the underside of the tailgate past ii Phillips head screws.

The left screw on both the driver and rider side light housings is the longer screw that holds the unabridged housing to the tailgate.

The right screw on both the driver and rider side low-cal housing is the shorter screw that merely holds the lens cover in place.

If y'all would similar to quickly modify a burnt out bulb, y'all only need to remove the shorter screw on the correct side of either the commuter or rider side light housings.

I removed both screws on the low-cal housing since I didn't realize that information technology was but necessary to remove the shorter correct side screw in order to change the bulb.

Two Screws Removed
Pull Out Light Housing
Light Housing Removed If you would like to remove the entire housing, remove both screws and set them bated in a rubber place.

(If yous merely removed the shorter right side spiral, simply pull off the translucent plastic lens cover from the forepart of the light housing. Then pull the one-time seedling straight out and push button in a new one. Supplant the lens cover and the shorter right side spiral to stop the task.)

Pull the unabridged housing abroad from the tailgate.

Button In Release Tab
Power Plug Asunder
Pull Off Lens Encompass Push in the release tab on the grey plastic electrical connector.

Pull the power plug directly out of its socket.

Lens Encompass Removed
Pull Out One-time Low-cal Bulb
Empty Bulb Socket Pull off the lens cover.

Pull the old light bulb direct out of the socket.

Old Light Bulb Removed
Push In New 168 Seedling
Snap On Lens Cover Push button a new miniature wedge base number 168 light bulb straight into the socket.

If you would like to have brighter license plate lights, install some compatible 168 LED bulbs.

Gently pop the lens encompass back into identify over the housing.

Lens Encompass Replaced
Dorsum Side of Housing
Right Screw - Holds Lens If y'all expect at the back side of the housing, you lot'll see that just the pigsty on the left side goes all the way through.

Replace the shorter correct screw to secure the lens cover in place by turning information technology in the clockwise direction with the Phillips head screwdriver.

Push button On Power Plug
Left Screw - Holds Housing
Tighten Spiral Clockwise Push the electric connector back into its socket.

It should "click" securely into place.

Button the calorie-free housing back into the opening in the underside of the tailgate.

Replace the longer screw into the hole on the left side of the housing to secure information technology to the tailgate.

Passenger Side Housing
Correct Side Spiral Holds Lens
Left Screw Holds Housing Repeat the process to replace the license plate light bulb on the other side of the SUV.

Again, the left screw is the longer one that holds the housing to the tailgate.

The right spiral is the shorter 1 that merely holds the lens cover in place.

Long Left Side Screw
Pull Out Light Housing
Pull Off Lens Encompass To easily change the other bulb, I recommend just removing the shorter spiral on the right side of the housing.

Then gently pull off the lens cover, pull the old light bulb and push in a new number 168 bulb.

Replace 2nd Low-cal Seedling
Pop On Lens Cover
Shorter Right Side Spiral Push the lens comprehend dorsum into place over the housing.
Tighten Clockwise
Re-Insert Light Housing
Longer Left Screw Supersede the screw or screws past turning them in the clockwise direction with the Phillips head screwdriver.
Tighten Clockwise
Test New Light Bulbs
Testing License Plate Lights To test the new license plate low-cal bulbs, plow on the parking lights, turn on the headlights or simply printing the "Unlock" push button on the cardinal fob to activate the exterior lights.

Exist sure to record the bulb alter in your SUV'south service records.

For more, please check out all of my 2001-2006 Acura MDX DIY Repair & Maintenance Guides.

Source: https://www.paulstravelpictures.com/Acura-MDX-License-Plate-Light-Bulbs-Replacement-Guide/

Posted by: helgesonafror1942.blogspot.com